THERMOMECHANICAL ANALYSIS OF PLASTIC DEFORMATION BEHAVIOUR IN DIELESS DRAWING OF METALLIC MATERIALS

Mariana POP, Adriana NEAG, Dan FRUNZA, Florin POPA

Abstract


Abstract: The dieless drawing of wires and bars is incremental plastic deformation process that has some significant advantages compared to the classic ones. In the process, the temperature and plastic deformation affect each other, so the deformation behavior is very complicated. The maximum reduction of the diameter, the influence of the drawing speed and the temperature are investigated. Changes in microstructure and hardness were investigated. As a result of the process, the grain structure was very deformed in the direction of the drawing. Any defects occurred were due to interruptions in the material microstructure caused by a high necking rate, shorter exposure time to the process temperature and low heating and cooling rates.

Key words: dieless drawing, plastic deformation, temperature, drawing speed


Full Text:

PDF

References


Handbook of Workability and Process Design, Edited by George E. Dieter Howard A. Kuhn S. Lee Semiatin, ASM International, 2003;

Weiss, V, Kot, R., Dieless wiredrawing with transformation plasticity, Wire Journal (9), p.182, 1969;

Tiernan, P., Hillery, M.T., Dieless wiredrawing-an experimental and numerical analysis, Journal of Materials Processing Technology, Volumes 155-156, 2004, Pg 1178-1183;

Tiernan, P., Hillery, M.T., An analysis of wire manufacture using the dieless drawing method, Journal of manufacturing processes, 10, 2008, pp 12-20;

Tiernan, P., Carolan, R., Twohig, E., Tofail, S.A.M., Design and development of a novel load control dieless rod drawing system, Journal of manufacturing science and technology, 4, 2011, 110-117;

Tiernan, P., Hillery, M.T., Experimental and numerical analysis of the deformation in mild steel wire during dieless drawing, Journal of Materials Design and Applications 216 (3), pp. 167-178, 2002 ;

Twohig, E., Tiernan, P., Tofail, S.A.M., Experimental study on dieless drawing of nickel-titanium alloy, Journal of the Mechanical Behaviour of Biomedical Materials, 8, 2012, pp 8-20;

Twohig E., Tiernan P., Butler J., Dickinson C., Tofail S.A.M., Mechanical, microstructural and thermal properties of a 50:50 at.% nickel–titanium alloy subjected to a dieless drawing process, Acta Materialia, 68, 140-149, 2014;

Pawelski, O., Kolling, A., Calculation of temperature distributionin dieless drawing, Steel Research(66), pp.50, 1995;

Pawelski, O., Rasp, W., W. Wengenroth, Investigation into processing of bars with variable cross-sections by dieless drawing, Proc. Of the 6th International Conference on Technology of Plasticity, 1999;

Furushima, T., Manabe, K., Experimental and numerical study on deformation behaviour in dieless drawing process of superplastic microtubes, Journal of Materials Processing Technology, Volumes 187-188, 12, pp 236-240, 2007;

Furushima, T., a Manabe,K., Experimental study on multi-pass dieless drawing process of superplastic Zn-22%Al alloy microtubes, Journal of Materials Processing Technology, 12, 2007;

Furushima, T., Sakai, T., Manabe, K.,Finite element modeling of dieless tube drawing of strain rate sensitive material with coupled thermomechanical analysis, Proc. of 8th Int. Conf. on Numiform, p.522, 2004;

Rus A., Frunză D., Hot deformation behavior for a thermomechanical processed 2014 aluminum alloy by tensile test, Acta Technica Napocensis, Series: Applied mathematics, mechanics and engineering, Vol 58, Issue III, 2015;

Rus A., Effect of thermo-mechanical treatments on the hot deformation, Acta Technica Napocensis, Series: Applied mathematics, mechanics and engineering vol 60, Issue III ,2017,

Mureşan C., G. Achimaş, N.Mihăilescu, Means for improving the quality of large diameter bent pipes with numerical simulation in the deformation process, Acta Technica Napocensis Series: Applied Mathematics and Mechanics Vol. 56, Issue I, 2013.


Refbacks

  • There are currently no refbacks.


JOURNAL INDEXED IN :