RESEARCH OF FUEL INJECTION DUTY ON A SPARK IGNITED ENGINE

Doru-Laurean BĂLDEAN

Abstract


Using a spark ignited Mitsubishi engine, with a volumetric capacity of 1997 cm3, this study presents the testing results of fuel injection duty and ignition advance in relation to the manifold pressure and throttle position. The later parameters are controlled by the driver’s applied force upon the accelerator pedal. Displacement of the last one is digitally translated or encoded as engine’s load. Peak value of the crank-shaft speed in this case study is close to 3000 rpm.

Full Text:

PDF

References


Andrei, L., et al, Applied Measurements and Instrumentation for Improving Diagnostic Devices and Systems in Metropolitan Polluted Environments with Nitric and Carbon Oxides, IFMBE Proceedings book series (IFMBE, volume 71), MEDITECH 2018, ClujNapoca, 2018.

Bățagă, N., et al, Internal combustion engines/Motoare cu ardere internă, Editura Didactică și Pedagogică, ISBN 973-30-4922-0, București, 1995.

Borza, E.V., et al, Research Concerning Fuel Economy Coefficient and Carbon Foot Print in Various Conditions for a City Compact Size Vehicle with Digital Control for a Green Solution and Method at Technical University from Cluj-Napoca, Proceedings of the International Congress of Automotive and Transport Engineering, In: Burnete N., Varga B. (eds) Proceedings of the 4th International Congress of Automotive and Transport Engineering (AMMA 2018). Proceedings in Automotive Engineering. Springer, Cham, pp. 181-189, ISBN978-3-319-94408-1.

Botean, A.I., Influence of working fluid pressure on the power of a Stirling gamma engine, Acta Technica Napocensis-Series: Applied Mathematics, Mechanics, and Engineering, 61 (2), 2018. Accessed July 3, 2019.

Botean, A.I., Optimization of a Γ-Type Stirling engine performance based on an experimental approach, Acta Technica Napocensis-Series: Applied Mathematics, Mechanics, and Engineering, 62 (2), 2019. Accessed Sept. 3, 2019.

Cherecheș, I.A., et al, Contribution of developing advanced engineering methods in interdisciplinary studying the piston rings from 1.6 spark ignited Ford engine at Technical University of Cluj-Napoca, IOP Conf. Ser.: Mater. Sci. Eng. 252 012072, doi.org/10.1088/1757-899X/252/1/012072, 2017.

Crișan-Lupa, L.V., et al, Research applied to exhaust gas after-treatment systems in 1.6 L Zsg 416 Ford engine, In: Andreescu C., Clenci A. (eds) Proceedings of the European Automotive Congress EAEC-ESFA 2015. Springer, Cham, Online ISBN 978-3-319-27276-4, 2015.

Cordoş, N., et al., Automobiles. Construction. Wear. Evaluation / Automobile. Construcţie. Uzare. Evaluare, Ed. Todesco, ISBN 973-99779-7-9, Cluj-Napoca, 2000.

Ferenți, I., et al., Artificial intelligence implemented in rally vehicles for increasing energetic efficiency in competitions / Inteligența artificială implementată în autovehicule de raliuri pentru creșterea eficienței energetice în competiții,Science and engineering/Știință și inginerie, 34 (18), Mai 29, 2018. Accessed June 3, 2019.

Ferenți, I., et al., The analize of specific parameters for spark ignited engine operational cycle depending on altitude/Analizamărimilorspecificecicluluifuncțional al unui motor cu aprindereprinscânteieînraport cu altitudinea,Science and engineering/Știință și inginerie, 26 (46), January 31, 2015. Accessed June 3, 2019.

Hodor, A., et al., Some considerations about 3D replication of complex surfaces, Acta Technica Napocensis-Series: Applied Mathematics, Mechanics, and Engineering, 56 (1), 2013. Accessed July 3, 2019.

Marincaș, C., et al., Contributions to the experimental research of Electronic Diesel Control (EDC) module operation in relation with supply of the N47 engine from BMW 320d (E90) automobile, Science and engineering/Științășiinginerie, 31 (82), May 3, 2017. Accessed July 3, 2019.


Refbacks

  • There are currently no refbacks.


JOURNAL INDEXED IN :