EXPERIMENTAL INNOVATION TO COMPENSATE POSITIONING INACCURACIES OF INDUSTRIAL ROBOTS WITH HIGH PAYLOAD CAPACITY

Răzvan Ioan HAPCA, Stelian BRAD, Vasile Dragoş BARTOŞ

Abstract


The issue of the absolute accuracy of large and very large industrial robots while handling heavyweights is still a challenge in the world of robotic engineers due to complex structural deformations in the robot joints and control modelling. It is almost impossible to master the reactions of these robots in complex industrial applications, where introducing small variations such as variable weights, variable gauges, and variable part models, positioning accuracy is strongly affected at high working speeds. In this paper is presented a methodology about measuring, compensating, and predicting the positioning errors of end-effector’. Measurements are done with metrologically certified instruments, like spacing measuring instruments, and comparator watches. An error prediction model is constructed to find out the positioning error at the tool center point (TCP) of the robot, for different payloads and different distances of the TCP relative to the robot base system. Tests indicate very good results for payloads above 550 kg, TCP speeds of 1000 mm/s and target points at over 3500 mm from the robot base.

Full Text:

PDF

References


Pan, Η., Polden, J., Larkin, N., Van Duin, S. and Norrish, J., "Recent progress on programming methods of industrial robots", Robot. CIM-Int. Manuf., Vol. 28, No 2, pp. 87–94, 2012.

Berg, J.O., "Robot Accuracy: A Matter of Programming", The Int. J. of Adv. Manuf. Technology, Vol. 7, No. 4, pp. 193-197, 1992.

ISO 9283 - "Manipulating industrial robots. Performance criteria and related test methods", ISO, Geneva 1998.

Elatta, A.Y., Gen, L.P., Zhi, F.L., Daoyuan, Y. and Fei, L., “An Overview of Robot Calibration”, Inform. Techn. J., Vol. 3. No. 1, pp. 74-78, 2004.

Visher, P. and Clavel, R., "Kinematic calibration of the parallel Delta robot", Robotica, Vol. 16, No 2, pp. 207-218, 1998.

Schröer, K., Bernhardt, R., Albright, S., Wörn, H., Kyle, S., van Albada, D., Smyth, J. and Meyer, R., "Calibration applied to quality control in robot production", Control Eng. Pract., Vol. 3, No. 4, pp. 575–580, 1995.

Wang, S., Miao, X., Yang Y. and Peng, X., “Error Compensation and Calibration of Inter-section Line Welding Robot Based on a Wavelet Neural Network”, in: T.-J. Tarn et al. (Eds.): Robotic Welding, Intelligence and Automation, Lecture Notes in Electrical Engineering series, Springer, 88, pp. 33–40, 2011.

Lee, M-S., Kang, D., Cho, Y.-S., Park, Y. and Kim, J.-H., "The effective kinematic calibration method of industrial manipulators using IGPS", in Proc. ICCAS-SICE, 2009, pp. 5059 - 5062.

Cui, H., Zhua, Z., Gan, Z. and Brogardh, T., "Kinematic analysis and error modeling of TAU parallel robot", Robot. CIM-Int. Manuf., Vol. 21. No. 6, pp. 497–505, 2005.

Shiakolas, P.S., Conrad, K.L. and Yih, T.C., "On the accuracy, repeatability and degree of influence of kinematics parameters for industrial robots", Int. J. Model. Simul., Vol. 22, No. 3, 2002.

Gong, C., Yuan, J. and Ni, J., Nongeometric error identification and compensation for robotic system by inverse calibration", Int. J. Mach. Tool. Manuf., Vol. 40, No 14, pp. 2119-2137, 2000.

Jang, J.H., Kim, S.H. and Kwak, Y.K., "Calibration of geometric and non-geometric errors of an industrial robot", Robotica, Vol. 19, No. 3, pp. 311–321, 2001.

Watanabe, A., Sakakibara, S., Ban, K., Yamada, M., Shen, G. and Arai, T., "A Kinematic Calibration Method for Industrial Robots Using Autonomus Visual Measurement", CIRP Ann. – Manuf. Techn., Vol. 55, No. 1, pp. 1-6, 2006.

Yin, J. and Gao, Y., "Pose Accuracy Calibration of a Serial Five DOF Robot", Energy Procedia, Vol. 14, pp. 977-982, 2012.

Shirinzadeh, B., Teoh, P.L., Tian, Y., Dalvand, M.M., Zhong, Y. and Liaw, H.C., „Laser interferometry-based guidance methodology for high precision positioning of mechanisms and robots", Robot. CIM-Int. Manuf., Vol. 26, No. 1, pp. 74-82, 2010.

Abtahi M., Pendar, A., Alasty, H. and Vossoughi, G., "Experimental kinematic calibration of parallel manipulators using a relative position error measurement", Robot. CIM-Int. Manuf., Vol. 26, No. 6, pp. 799-804, 2010.

Nubiola, A. and Bonev, I.A., "Absolute calibration of an ABB IRB 1600 robot using a laser tracker", Robot. CIM-Int. Manuf., Vol. 29, No. 1, pp. 236-245, 2013.

Alici, G, and Shirinzadeh, B., "A systematic technique to estimate positioning errors for robot accuracy improvement using laser interferometry-based sensing", Mech. Mach. Theory, Vol. 40, No. 8, pp. 879–906, 2005.

Tao, P.Y., Yang G. and Tomizuka, M., "A Sensor-based Approach for Error Compensation of Industrial Robotic Workcells", 2012 IEEE Int. Conf. on Robotics and Automation, Saint Paul, Minnesota, USA, May 14-18, 2012, pp. 5240-5245.

Santolaria, J. and Ginés, M., "Uncertainty estimation in robot kinematic calibration", Robot. CIM-Int. Manuf., Vol. 29, No. 2, pp. 370-384, 2013.

Alici, G., Jagielski, R., Sekercioglu, Y. and Shirinzadeh, B., "Prediction of geometric errors of robot manipulators with Particle Swarm Optimisation method", Robot. Auton. Syst., Vol. 54. No. 12, pp. 956–966, 2006.

Kim, K., Lee, S., Kim, K., Lee, K-Y., Heo, S., Park, K., Jeong, J-I. and Kim, J., “Development of the end-effector measurement system for a 6-axis welding robot”, Int. J. Prec. Eng. Manuf., Vol. 11, No 4, pp. 519-526, 2010.

Benardos, P.G. and Vosniakos, G.-C., “Optimising feedforward artificial neural network architecture”, Engineering Applications of Artificial Intelligence, Vol. 20, No. 3, pp. 365-382, 2007.

Shiels, Maggie, "Legal milestone for open source" BBC News. Retrieved 2008-08-15 (http://news.bbc.co.uk/2/hi/technology/7561943.stm accessed on May 20, 2018)

Angelidis, A. and Vosniakos, G.C., “Prediction and compensation of relative position error along industrial robot end-effector paths”, International Journal of Precision Engineering and Manufacturing (Springer), Vol. 15, No. 1, pp. 63-73, 2014.


Refbacks

  • There are currently no refbacks.


JOURNAL INDEXED IN :