SELECTION OF A METHOD FOR MACHINING AN ARCHIMEDEAN SPIRAL GROOVE

Bruno RĂDULESCU, Andrei Marius MIHALACHE, Mara RĂDULESCU, Laurențiu SLĂTINEANU, Adelina HRIȚUC, Oana DODUN, Gheorghe NAGÎȚ, Margareta COTEAȚĂ

Abstract


The problem of machining a spiral groove in a metal workpiece was raised to achieve a device for evaluating the thermal expansion capacity of plastics. It was found that a groove in the form of an Archimedean spiral corresponds to the requirements derived from the operation of a device conceived for developing scientific research. Five alternatives for the machining of the groove have been identified, and the imposed decision method was used to select the most convenient machining alternative. The use of this method involved a comparison of the alternatives two by two and based on previously established criteria to select the alternative of machining the groove in the form of an Archimedean spiral. It was found that for the conditions considered, the most convenient alternative is machining on a milling machine equipped with a numerical control subsystem.


Full Text:

PDF

References


Zhang, P., Gu, B., Zhou, J., Wei, L., On hydrodynamic lubrication characteristics of ferrofluid film in a spiral groove mechanical seal, Industrial Lubrication and Tribology, 70, 9, 1783-1797, 2018

Furuishi, Y., Suganami, T., Yamamoto, S., Tokumitsu, K., Performance of water-lubricated flat spiral groove bearings, Journal of Tribology, 107, 2, 268-272, 1985

Spiral groove thrust bearing, https://www.tribology-abc.com/calculators/e9_4.htm

Bai, S., Peng, X., Meng, Y., Wen, S., Modeling of gas thermal effect based on energy equipartition principle, Tribology Transactions, 55, 6, 752-761, 2012

Velescu, C., Calin Popa, N., Laminar motion of the incompressible fluids in self-acting thrust bearings with spiral grooves, The Scientific World Journal, vol. 2014, ID 478401, 2014

Flitney, R. Seals and Sealing Handbook, 6th Edition, Butterworth-Heinemann, ISBN: 9780080994161, 2014

Fundamentals of surface generation. Cutting of gears (in Romanian), https://www.cmmi.tuiasi.ro/docs/cursuri/Danturarea%20rotilor%20dintate.pdf

Picoș, C., Machine Manufacturing Technology, Editura Didactică și Pedagogică, București, 1974

Bercovici L., Milling machining strategies. Circular pocket machining by the two-center flat spiral method. Programming algorithm (in Romanian), 2013, https://www.ttonline.ro/revista/masini-unelte/procedura-de-programare-si-reglare-a-masinilor-unelte-comandate-numeric

Humpa, M., Köhler, P., Design approach for spiral milling parts using knowledge based engineering, 27th International Conference on CADCAM, Robotics and Factories of the Future 2014, IOP Conf. Series: Materials Science and Engineering vol. 65, 012001, 2014

Kalinovsky, D., Turning operation on CNC machine in metalworking industry. Cutting tool makes spiral groove on metal detail face. https://www.dreamstime.com/turning-operation-cnc-machine-metalworking-industry-cutting-tool-makes-spiral-groove-metal-detail-face-spiral-grooving-image220061588

Hrituc, A., Nagîț, G., Dodun, O., Slătineanu, L., Measuring the length of a spiral when evaluating the plastic processability by injection molding, 2019, IOP Conf. Ser.: Mater. Sci. Eng., 564, 012025, 2019

Slătineanu, L., Fundamentals of scientitfic research (in Romanian). Publishing House PIM, ISBN 978-606-13-4903-6, Iași, 2019

Belous, V., Inventics (in Romanian). Publishing House Asachi, ISBN 10: 973956500X ISBN 13: 9789739565004, Iași, 1992


Refbacks

  • There are currently no refbacks.


JOURNAL INDEXED IN :